All the Variety Without the Extra Work!
EasyPatterns® are the wow factor you're looking for! These pre-printed patterns eliminate the need for layering multiple solid colors, therefore eliminating extra weight on the garment! Available in styles ranging from classic to cool, there’s bound to be a pattern that's perfect for your next project. EasyPatterns were designed to fit into a variety of vinyl cutters as easily as they fit into a variety of niches and trends. Simply cut in the positive (do not mirror) with the pattern facing up, weed away the excess from the static carrier, and mask with TTD High Tack and a squeegee. After heat application, the mask releases quick and easy while still warm. Mix and match EasyPatterns with other types of Siser HTV for extraordinary styles. Just be sure to keep EasyPatterns as the top layer for best results. With a semi-gloss finish and soft hand, EasyPatterns are the star of the show even when applied with a home iron!
EasyPatterns are 80 Microns / 3.1 Mils and are a PU composition.
These are 12" x 30ft rolls.
Are you looking for smaller quantities? We have 12"x12" sheets and 12"x5ft rolls also.
Please Note: Due to increased heat and humidity during the summer months, we recommend allowing TTD Masks to return to indoor room temperature (below 70°F/21°C) before use for best performance. If additional cooling is needed, TTD Masks can be placed inside a fridge or freezer for 5- 10 minutes.
Siser EasyPatterns HTV is:
- Laser Friendly
- Layerable
- Iron-On friendly
- CPSIA Certified
Siser EasyPatterns HTV Applies To:
- 100% Cotton
- 100% Polyester
- Poly/Cotton Blends
- Leather
Craft Cutter Settings
|
Cricut:
Blade: Standard Setting: Iron-on
|
Silhouette Cameo:
Blade: Standard, 2 Material: Heat Transfer, Smooth Speed: 8 Force: 6 |
Brother ScanNCut:
Blade: Standard, 2 Cut Speed: 1 Cut Pressure: 1 |
|
Pro Cutter Settings
Roland GX/GS-24:
Blade: 45° Gram Force: 80-90 Offset: .250 Speed: 25-50 cm/s |
Graphtec:
Blade: 45° Force: 9 Tool: CB09+0 Speed: 25 cm/s |
MH, SC2, LP3, and Titan 1:
Blade: 45°/60° Gram Force: 80-85 Speed: 300 mm/s *Blade Advancing Varies |
Titan 2 & 3:
Blade: 45°/60° Gram Force: 60-65 Speed: 300 mm/s *Blade Advancing Varies |
Mimaki CG-60SRIII:
Blade: 45° Gram Force: 90 Offset: 30 Speed: 20-30 cm/s |
|
Settings may vary based on blade condition and age of machine. Always perform a test cut prior to cutting designs.
Application Instructions
|
Home Iron Instructions
• Cut design in positive (Do not mirror)
• Mask with TTD Mask
• Set iron dial between Cotton and Linen
• Cover with Heat Transfer Cover Sheet or Multipurpose Paper
• Place on flat, hard surface (ironing board not recommended)
• Press iron with medium/firm pressure (do not slide iron)
• Press each section of design for 15 seconds
• If areas of design lift after application, replace cover sheet and
re-press for 10 seconds
• Peel carrier hot or cold
|
Heat Press Instructions
• Cut design in positive (Do not mirror)
• Mask with TTD Mask
• Set iron dial between Cotton and Linen
• Cover with Heat Transfer Cover Sheet or Multipurpose Paper
• Preheat garment for 2-3 seconds
• Apply design at 305°F/150°C
• Use medium pressure for 10-15 seconds
• Peel carrier hot or cold |
|
Laundering Instructions
- Wait 24 hours before first wash
- Machine wash warm or cold / mild detergent
- Dry on normal dryer setting
- Do not dry clean
Click here for downloadable Siser HTV application instructions
Recommended Accessories
Heat Transfer Cover Sheet
TTD Masking Material (Carrier Sheet)
